Instructor Panel
Shared Aircraft & Navigation State — drives all units
All
ADI
HSI
MFD
Fail
Aircraft
Heading
312°
Track follows heading (no wind)
Track (over ground)
312°
Groundspeed
120kt
▶ Start Flight
Current Track is the magenta diamond on the HSI compass rose. Uncheck "Track follows heading" to set a crab angle/drift independent of Heading — e.g. nose pointed 10° right of the actual ground track in a crosswind.
Failures & Degraded States
AHRS fail (attitude + heading)
AHRS aligning
ADC fail (air data)
Heading degraded (yellow)
Heading unavailable
GPS position lost (LOI)
Clear all failures
AHRS fail implies heading loss. With heading unavailable the HSI shows GPS-derived track and bearing pointers are hidden, per the manual.
ADI — Attitude & Trend
Pitch
2.0°
Roll
-3°
Standard rate turn pointers
Pin to fixed demo angle
Demo angle
15°
Unpinned, the pointers track the bank needed for a standard rate turn at derived TAS. Pinned at 15° they sit midway between the 10° and 20° roll marks.
Slip/Skid
0.00
IAS trend (6s)
0kt
ALT trend (6s)
0ft
ADI — Airspeed / Altitude / Baro
Airspeed
120kt
Flaps range min
KT
Flaps range max
KT
Normal range min
KT
Normal range max
KT
Caution range min
KT
Caution range max
KT
VNE (red begins)
KT
Altitude
4500ft
Vertical Speed
-300fpm
Baro (hPa)
1013
Vspeed color bands are illustrative, not tied to a specific aircraft type. The white flaps arc is drawn in its own lane, right of (inboard from) the green/yellow/red arc, so it stays visible even when its range overlaps the normal range.
ADI — Flight Director
Flight Director command bars
FD pitch cmd
0.0°
FD roll cmd
0°
ADI — Minimums
Altitude minimum bug
Alt min source
BARO
RADIO
Alt min value
FT
Also settable on the instrument: swipe up → ADI Options → Minimums. Bug is cyan beyond 100ft, white within 100ft, yellow once reached, and shown dashed when parked at the end of the tape.
ADI — Deviation
Show lateral/vertical deviation (off by default per manual)
Navigation Source
Active source: VOR1 — changed by tapping the CDI button on the HSI/MFD, which cycles only through the sources ticked above (matching how a real CDI Source Button only cycles through installed/configured equipment). At least one source must stay ticked.
Vertical Guidance (ILS glideslope)
Always show (ignore source — not just LOC1)
Threshold elev
FT
Vertical Guidance normally applies only when the source is LOC1 ; tick "Always show" to display it regardless of source, for demonstrating the glideslope diamond without needing to cycle to LOC1 first. The station is treated as the runway threshold and a 3° glide path is computed from the aircraft's height above threshold and its range, driving the glideslope diamond on both the ADI and HSI.
Waypoint / Station
Distance
NM
Station bearing
°
Auto TO/FROM from bearing
Bearing is measured from the aircraft to the station and anchors a virtual station at that bearing and distance. While the flight is running the bearing is recomputed each tick, so TO/FROM flips by itself as the aircraft crosses the perpendicular to the selected course. Selecting a point on the MFD overrides this and uses that point's real geometry instead.
Nav phase
OCN
ENR
TERM
APR
Manual entry above is used only when no map point is selected (see MFD panel below).
External Navigator
OBS mode
SUSP (sequencing suspended)
On ILS/LOC approach
These are set by the external GPS navigator, not by the GI 275 — the manual states OBS Mode "can only be enabled by the selected external GPS navigator", so they belong here rather than on the instrument. Enabling OBS also suspends sequencing. With an ILS/LOC approach active and GPS still selected, the CDI button flashes to prompt a source switch.
Deviation
Auto (from course vs. heading)
Manual dots
0.0
Vertical Guidance
Show vertical scale (both units)
Deviation
0.0
Bearing Pointers (on the 'HSI' Page)
Bearing 1 (single line)
BRG 1
045°
Bearing 2 (double line)
BRG 2
200°
Annunciations
MSG flag (HSI unit)
MFD — Range & Layers
Show waypoints
Show VORs
Show airports
Show track vector
Look-ahead
30 sec
60 sec
2 min
5 min
10 min
20 min
Map Detail
4 (Most)
3
2
1 (Least)
Range Ring always on
Range Ring otherwise fades a few seconds after opening the map or changing range, per the manual. Map Detail 1 hides all points; 2 adds airports; 3 adds VORs and waypoints. Pinch to zoom is supported on the map face, in addition to the Small Knob.
MFD — Selected Point
Tap a waypoint, VOR or airport on the MFD
Reset to default scenario
Modelling notes. Unofficial training aid. Not affiliated with or endorsed by the manufacturer. Not for actual navigation. Modelled against Pilot's Guide 190-02246-01 Rev H.
Three physical units are shown — a Primary ADI, a Standby HSI, and an MFD — matching a real three-GI 275 panel. Per the manual's unit-configuration table, a Primary HSI only ever gets the 'HSI' and 'HSI Map' pages, but a Standby HSI (like Unit 2 here) or an MFD (Unit 3) also has an 'ADI' Page available — so both units can page through to a full attitude display via their Large Knob, alongside 'HSI' and 'HSI Map'. The Primary ADI (Unit 1) still has no other page. All ADI displays share the same underlying attitude/airspeed/altitude/heading data, so they always agree; Unit 1's is the most complete (V-speed bugs, standard rate pointers, minimums, extreme-attitude cues), while Units 2/3's ADI page is a slightly reduced view, similar to how a real standby attitude display is typically simpler than the primary. Neighbouring pages beyond that (CDI, Map, Traffic) are not implemented. The MFD map shows a synthetic decorative landscape only — it is not terrain data , carries no elevation meaning, and must never be read as such. Airspace and traffic are not modelled.
Known approximations: Airspeed colour bands and Vspeed defaults are set to published Piper PA-28-161 Warrior II POH values (Vs0 48 kt, Vfe 102 kt, Vs1 53 kt, Vno 127 kt, Vne 161 kt). The VLE slot on the V-speed bugs is repurposed as Va (111 kt) since this is a fixed-gear type. If configured to represent a different type these values must come from that type's POH. VOR/LOC angular deflection limits are conventional approximations, not certified values. True airspeed is derived from IAS by the ~2%-per-1000ft rule of thumb, not from a modelled air data computer, so the standard rate turn pointers are indicative only. Flight Director command bars are a simplified visual cue, not an AFCS mode-logic engine, and do not tilt with roll. Aural alerts (altitude alerting tones, "Minimums Minimums") are not produced — visual annunciations only. Waypoint/VOR/airport identifiers and positions are synthetic.